Short answer: a bowing or bulging brick wall means the wall is pulling away from the floors and roof that hold it in place. In old Philadelphia row houses it is usually caused by water damage, rotted joist ends or failed ties. Small movement can be monitored and tied back; serious bulging is a safety problem that needs a structural engineer, and if L&I cites it, a make safe permit.
Warning signs to look for
Walk around the house, inside and out, and look for these signs:
- A belly in the wall. Hold a straightedge or look along the wall from the corner. A visible outward bulge is the classic sign.
- Gaps where walls meet floors or ceilings. A crack opening along the edge of the floor or ceiling means the wall is moving away.
- Stair-step cracks in the brick or mortar. Especially cracks that grow or reopen after repointing.
- Doors and windows that stick. Openings near the wall go out of square as it moves.
- Loose or spalling brick and missing mortar. Water gets in and makes things worse.
- Sloping floors near the wall. The joist ends may have rotted or slipped out of their pockets.
Why row house walls bow
Philadelphia row houses lean on each other. The floor joists sit in pockets in the brick party walls, and the front and rear walls are held in place by the floors and roof. When that connection weakens, the wall starts to move. The usual causes:
- Water. Roof leaks, failed flashing, bad gutters and open mortar joints rot joist ends and wash out mortar.
- Rotted joist pockets. When the joist ends rot, the wall loses its bracing.
- A demolition or collapse next door. A party wall that was built to be shared suddenly has nothing on one side.
- Old renovations. Removed walls, cut joists or heavy new loads can overload the structure.
- Settlement. Soil movement, leaking pipes or nearby excavation can shift the foundation.
How bowing walls are repaired
The fix depends on how far the wall has moved and why. A structural engineer should make that call. Common repairs include:
- Fixing the water first. Roof, flashing, gutters and repointing. Without this, any repair fails again.
- Wall ties and anchors. Steel anchors or tie rods tie the wall back to the floor framing, often with visible star or plate anchors outside.
- Joist repairs. Sistering or replacing rotted joist ends and rebuilding the joist pockets.
- Partial rebuild. When a section is too far gone, it is taken down and rebuilt, with temporary shoring while the work is done.
- Party wall protection. After a neighbor’s demolition, the exposed wall may need bracing, weatherproofing and stucco or a new finish.
Bigger than a repair becomes demolition: if most of the framing is being replaced along with changes to an exterior wall, L&I can require a demolition permit instead.
When L&I gets involved
A bulging wall over a sidewalk is one of the most common reasons L&I issues an Unsafe or Imminently Dangerous violation. Inspectors often visit after a neighbor’s complaint, a 311 call or a nearby demolition. If you get one of these notices, the deadlines are short: about 10 days to comply for Imminently Dangerous and up to about 35 days for Unsafe. Read our guide on Unsafe vs. Imminently Dangerous violations.
Wall already cited by L&I? We coordinate the engineer, file the make safe permit, shore the wall and do the repair. Call (215) 501-7566.
What to do this week
If you see a bulge or new cracks:
1. Take photos and measure
Photograph the wall and mark the ends of cracks with a pencil and the date, so you can see if they grow.
2. Keep people clear
If brick is loose over a sidewalk, door or yard, keep people away from it.
3. Stop the water
Fix roof leaks, gutters and downspouts as soon as you can.
4. Call a contractor and engineer
A structural assessment tells you how serious it is and what repair is needed.
5. Get the permit
Structural wall repairs need a permit, and the engineer’s drawings or report support the application.
Worried about a bowing wall?
We inspect row house walls across Philadelphia, coordinate the engineer and handle the permit and the repair. Philadelphia contractor license #43984.
Bowing wall FAQs
Is a bowing brick wall dangerous?
It can be. Small, stable movement can often be tied back, but a wall that keeps moving or bulges over a sidewalk can fail. Have a structural engineer look at it.
What causes walls to bow in Philadelphia row houses?
Mostly water damage that rots joist ends and weakens mortar, plus demolitions next door, old renovations and settlement.
How is a bowing wall fixed?
Stop the water, then tie the wall back with anchors, repair the joists, or rebuild the worst sections, as designed by an engineer.
Do I need a permit to fix a bowing wall?
Yes, structural wall repairs need a permit from L&I. If L&I has already cited the wall as Unsafe or Imminently Dangerous, you need a make safe permit.
Who is responsible for a shared party wall?
It depends on the deed, the damage and the cause. Talk to your neighbor early, and to an attorney or your insurer if there is a dispute.
Related guides and services
Sources: City of Philadelphia, get a make safe permit; L&I, make safe permits and inspection requirements (Nov 2024); City of Philadelphia, violation and order types. Rules change, so always check your notice and confirm with L&I.

0 Comments